If Lifting the door by hand feels like lifting the car.
Then Spring tension adjustment or replacement.
The springs are meant to carry nearly all the weight; when they fade, the strain shifts to you and the opener. Torsion Spring Replacement

Plenty of houses in Brighton still open the wood or early steel door they were built with, often on extension springs. Those doors deserve a technician who knows them: how to true a sagging section, add safety cables, replace worn pulleys, and bring the hardware up to date without losing the look of the house. We also come out to Cankerville, Carman, Cedar Creek, Hilton, Spring Valley and Wade Corners.
Same fees day or night · Brighton
Pick the closest, or call (289) 677-1944
Repair & MaintenanceInspection, adjustment, sealing, and section-level repairs.
Springs & HardwareCounterbalance, track, roller, cable, and hinge work.
Openers & AccessOperators, safety sensors, controls, and access systems.
Installation & UpgradesResidential and commercial replacement, upgrades, sectional-door, and rolling-door work.We are careful about what we recommend in Brighton. If a tune-up will do, that is what we suggest. If a spring is the problem, we replace the spring and check its partner. If the door is beyond repair, we say so plainly. Every recommendation is one you can watch us justify at the door.
Nearby Cobourg, Alnwick/Haldimand, Cramahe, Hamilton, Gosport, East Colborne, Coverdale, Norham, Codrington, Orland and Smithfield
Measured carefully, fitted cleanly.
17 years in business · Send a few details about your door: (289) 677-1944
Brighton
People in Brighton call about garage doors for many reasons, and we have a service for each: the door that stopped, the one that got loud, the one that lets in cold air, the remote that died, the panel that got dented, and the door that has simply had its day.

Garage Door Opener Replacement, Garage Door Manual Lock Repair, New-Construction Garage Door Installation…
Tap a situation. The answer opens here.
If Lifting the door by hand feels like lifting the car.
Then Spring tension adjustment or replacement.
The springs are meant to carry nearly all the weight; when they fade, the strain shifts to you and the opener. Torsion Spring Replacement
If When you release the opener the door slides down on its own.
Then Balance adjustment.
A balanced door stays put at half height; drifting means the springs need winding or replacing. Garage Door Balance Adjustment
If The door flies up on its own and bangs the stops.
Then Spring tension reduction.
Too much tension is as hard on hardware as too little; a careful adjustment settles it. Torsion Spring Replacement
NorthumberlandOntario
Every square is one home in a hundred.
The knob is meant to grip the square spindle with a set screw, and that screw has loosened or the spindle's flat has worn so the knob no longer bites. Sometimes the spindle itself has sheared inside the door. The technician tightens a fresh set screw onto a proper flat or fits a new spindle of the correct length, and the knob and outside handle move as one again.
It helps to have someone present to open the garage, point out anything you noticed and hear how the door should feel afterwards. The technician needs power at the opener outlet, clear space under the shaft for a ladder, and access to both sides of the door. If a vehicle is inside, it stays until the door is working. Being there also lets you approve any extra items, such as bearings or cables, as they come up.
Age alone is not the test; parts and safety are. The technician checks the exact model and part numbers, because even a unit from the last two decades can have a board, sensor or trolley that is no longer made. Where the parts are available, a repair is usually straightforward. Where a key part is discontinued with nothing to replace it, or the unit predates photo eyes, replacement is the sounder choice even for a small fault. The technician tells you which side of that line your unit sits on.
Always, and after every adjustment, because changing tension, limits or force changes how the operator senses an obstruction. The door is closed onto a 38 mm block on the floor and must return to open on contact, then closed again while the low sensor beam is interrupted and must reverse the same way. If either test fails the settings are revisited until both pass, and you are shown the tests so you can repeat them monthly.
On-site assessment preferred · (289) 677-1944, open 24/7